Search:

Type: Posts; User: Bill Bennett

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    853

    The 345 heads can be bolted to the 304 block but...

    The 345 heads can be bolted to the 304 block but the 304 intake manifold will not seal against the 345 heads. The 345 intake manifold won't fit the 304 block because the 304 and 345 are different...
  2. Replies
    1
    Views
    723

    The 'C' trucks also had the 304 and 345 cu in V8...

    The 'C' trucks also had the 304 and 345 cu in V8 engine as factory options. The larger 392 cu in V8 became available in the 1969 'D' body trucks. There are a couple 4 speed trans and a couple 5...
  3. Replies
    1
    Views
    1,271

    If I remember, look at a Chevy switch from about...

    If I remember, look at a Chevy switch from about the same years production. The local auto electric shop replaced the switch in my 68 Travelall.
  4. Would help to know which carb is on the engine....

    Would help to know which carb is on the engine. What is your operating elevation. If a 2nd shot on the accelerator seems to help the problem, then a larger shot from the accelerator pump may fix the...
  5. Thread: Film

    by Bill Bennett
    Replies
    1
    Views
    3,796

    Look in the photography magazines in the ad...

    Look in the photography magazines in the ad section. Then find someone to process the film using the correct chemicals for whatever film you might use.
  6. Replies
    3
    Views
    6,404

    Before asking how to get better mileage, it will...

    Before asking how to get better mileage, it will help to know what mileage you are getting now? What trans, what final gear ratio, what diameter tires. I think most IH owners will recommend getting...
  7. Replies
    10
    Views
    2,204

    The #4412 designation is a 500 cfm carb. More for...

    The #4412 designation is a 500 cfm carb. More for racing than IH service. Some owners have been kinda happy with the carb but not many. The smaller #7448 - 350 cfm carb is still overcapacity for the...
  8. Replies
    10
    Views
    2,204

    Look at the carb of picture #4 of 5. Could be the...

    Look at the carb of picture #4 of 5. Could be the Holley 350 cfm 2bbl carb. Is there a part number on the face of the intake?
  9. Replies
    5
    Views
    1,699

    There is a 'C' truck being scrapped out in...

    There is a 'C' truck being scrapped out in Washington by 'The Fleckster'. He may have what you need. On Binder Planet.
  10. What motor and transmission is/was in the truck?

    What motor and transmission is/was in the truck?
  11. Replies
    2
    Views
    724

    Only you would know how old the in-line filter...

    Only you would know how old the in-line filter is. When in doubt, change it out! Check the fuel pressure at the carb and the rubber hoses connections. Looking for about 5 to 5 1/2#. The Ethanol in...
  12. Replies
    1
    Views
    532

    Best bet will be to take it to your local...

    Best bet will be to take it to your local radiator repair shop. If the cap needs to be removed, you can check the condition of the core as well.
  13. Replies
    5
    Views
    1,955

    While waiting for delivery, go to the beach and...

    While waiting for delivery, go to the beach and look at the 'tread pattern' used by the lifeguard trucks. They are driving on the sand all day.
  14. Replies
    5
    Views
    1,955

    What engine is in the truck? Which transmission?...

    What engine is in the truck? Which transmission? What is the present differential gear ratio? What size tires and wheels are on the truck? What is your location/elevation?
  15. Replies
    2
    Views
    938

    A picture might help.

    A picture might help.
  16. Replies
    2
    Views
    665

    How about using a 'red' bulb? Paint the inside of...

    How about using a 'red' bulb? Paint the inside of the bucket with white paint and cut the lid of a small pineapple can to fit behind the bulb. Center the lid 'rings' behind the bulb.
  17. 4464Get your chin right down on the passenger...

    4464Get your chin right down on the passenger side fender and look past the back side of the alternator and just below the front edge of the exhaust manifold. There should be a picture attached...
  18. Replies
    12
    Views
    1,946

    How many miles on the motor and what brand oil...

    How many miles on the motor and what brand oil and oil filter are you using? The 10-30 oil is thin for the IH motor except maybe in Alaska - in winter.
  19. Replies
    4
    Views
    3,175

    That is correct, the motors are different. The...

    That is correct, the motors are different. The intake manifold for the AMC will not fit the IH 304. With the low RPM range of the IH engine compared to the AMC engine, you don't need the 4bbl carb....
  20. Replies
    4
    Views
    1,034

    What 'custom touches' are you considering?

    What 'custom touches' are you considering?
  21. Replies
    4
    Views
    1,034

    Is your plan to keep it for years or just clean...

    Is your plan to keep it for years or just clean the dust out and re sell it? The double doors are better if towing is planned.
  22. Replies
    4
    Views
    1,127

    The original head gaskets were a thin steel...

    The original head gaskets were a thin steel gasket. Replacement head gaskets are the thicker composite material. The additional gasket thickness will lower the compression ratio and result in lower...
  23. Replies
    12
    Views
    2,890

    4234That bracket was for the plastic windshield...

    4234That bracket was for the plastic windshield washer bottle. Not important. The washer bottle from a Scout II will fit in the same space and the electric pump motor is built into the bottle....
  24. Replies
    11
    Views
    2,439

    Is the idle speed correct? Will the engine keep...

    Is the idle speed correct? Will the engine keep running if the throttle is feathered? Have you tried adjusting the idle mix screws on the carb?
  25. At one time, I remember there was a tool with -...

    At one time, I remember there was a tool with - like a socket head attached to a short handle. There was a 'knob' at the socket end that used a short shaft through the socket, with a blade...
Results 1 to 25 of 154
Page 1 of 7 1 2 3 4