Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: Scout 80/800 parts firesale 1 wk only

  1. #1
    Join Date
    Jun 2009
    Location
    Maryland
    Posts
    145

    Default Scout 80/800 parts firesale 1 wk only

    Scout 800 T18 4 speed transmission for a 152/196 4 cyl engine only. Transmission, twin stick D20 transfer case, 4 cyl pancake bellhousing, T/O bearing with sleeve. Can be made to work with a 4 cyl Scout 80 with some fabrication. All for $275.00.

    Scout 800 v8 model T90 and D20 with bell $125


    EVERYTHING BELOW THIS LINE IS SOLD

    Scout 800 v8 T18 4 speed transmission for a v8 engine only (could work for a 6 cyl????) with single stick D20 transfer case, NO BELLHOUSING, use one from a Scout II or truck, $250.00

    SII 345 with thermoquad 4BBL, mostly complete, had about 110K on it prior to removal, ran great when removed, comes with 727 flexplate, spacer and torque converter but no trans, rotten air injection lines you should just plug them anyway, great motor $250.00. I was going to put this in an 800 but got a 392 so this 345 moved to the side......yes it will work in an 800 you need to move over your accessories and wiring harness if you want it to be "quick and painless"

    Scout 800 Borg Warner 11 automatic, v8 bellhousing, torque converter and flexplate, D20 transfer case, heat exchanger, shifter assembly. $250.00.

    new fiberglass Kentrol passenger rear 1/4 panel, Scout 80/800, never used, go online and compare prices. $200.00 less than 1/2 price.

    304 out of a truck, ran good prior to removal, I replaced the freeze plugs for re-installation of engine then sold the truck, can be used in a Scout if you move over your oil pump and pan. $100.00 no carb and some accessories are not there (you would probably need to put your Scout accessories on anyway for fitment).

    Good running Scout 800 v8 266 $200 mostly complete

    Scout 800 304, T90 trans with single stick D20, runs OK needs tuning, $300 complete setup

    SII 196 mostly complete will drop into a v8 Scout 800 frame but will need slight modification to be used to replace a Scout 800 152 or 196 $200

    Scout 80/800 152 never ran it, loose and mostly complete $50.00

    I desperately need the room and at least need to disposition these items immediately if not sooner.

    Free shipping to Nationals but you will need to have something to remove it/them from my flatbed. Otherwise truck freight. I will load on a pallet and help with but not arrange shipping.
    Last edited by stu simpson; 09-06-2009 at 02:00 AM. Reason: adjust information

  2. #2
    Join Date
    Apr 2009
    Posts
    4

    Default Carb

    Looking for a good rebuildable carb for a 69' 196. Thanks.

  3. #3
    Join Date
    Jun 2009
    Location
    Maryland
    Posts
    145

    Default carb

    Quote Originally Posted by KansasScout View Post
    Looking for a good rebuildable carb for a 69' 196. Thanks.
    Sorry don't have that

  4. #4
    Join Date
    Jun 2009
    Location
    Hurlburt Field, FL
    Posts
    495

    Default

    Hey Stu, you got any AC stuff for the Scout II? I'm needing the under-dash parts for mine.

  5. #5
    Join Date
    Jun 2009
    Location
    Maryland
    Posts
    145

    Default SII stuff

    Sorry, I do not have any Scout II stuff other than the engine and axles which I acquired as individual pieces.

  6. #6
    Join Date
    Sep 2009
    Location
    Massachusetts
    Posts
    6

    Default

    Stu,

    Scout 800 T18 4 speed transmission for a 152/196 4 cyl engine only. Transmission, twin stick D20 transfer case, 4 cyl pancake bellhousing, T/O bearing with sleeve. Can be made to work with a 4 cyl Scout 80 with some fabrication. All for $275.00.
    Is this 4 cyl 4 spd still available?

    Thanks,
    binderboy

  7. #7
    Join Date
    Jun 2009
    Location
    Maryland
    Posts
    145

    Default transmission

    Yes since I had 2 of them one remains, but needs to be pulled. I am not sure if I can get to this by Nationals, is that what you needed or can we meet up sometime later?

  8. #8
    Join Date
    Sep 2009
    Location
    Massachusetts
    Posts
    6

    Default 4 cyl 4 Spd Transmission

    Stu,

    Yes since I had 2 of them one remains, but needs to be pulled. I am not sure if I can get to this by Nationals, is that what you needed or can we meet up sometime later?
    Yes, we can meet up later, that's fine. No need to have it done by Nationals as I won't be there. No rush, just let me know when you get around to it.

    Thanks,
    binderboy

  9. #9
    Join Date
    Jun 2009
    Location
    Maryland
    Posts
    145

    Default transmission

    Best thing for you to do is either email me your contact info or call me soon so it stays on the radar.

    I have to get something bulky to Conneticut so maybe we can work something out.

    stu
    443-277-8258

  10. #10
    Join Date
    Jun 2009
    Location
    Maryland
    Posts
    145

    Default Update

    Parting out:

    1963 Scout 80 no axles

    2X 1961-63??? Scout 80s, welded bulkheads, one with semi crushed halfcab, decent tub, doors off

    Unknown year Scout 800 Sportop 4x4 either 66 or 67 thats all I can say

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •